ONLY FITS THE CURRENT MODEL TREEMOTION PRO and ESSENTIAL
You can replace the hip/leg assembly relatively easily, but a suitably qualified person should undertake the work
Minimal tools required (TORX-20)
Made in the Austria by Teufelberger
The DMM Webbing Stopper Kit makes a better alternative to the original rivets

PLEASE NOTE: Adequate training and judgment are needed to reduce the risks inherent in using this equipment. The purchaser's responsibility is to ensure they are competent in using this product. Treetools strongly advise that you do not use any height safety or arborist equipment without first undertaking appropriate training.

No responsibility will be accepted by Treetools for damage, injury or death resulting from incorrect assembly or modification. If in doubt, contact Treetools at richard@treetools.co.nz. Any person modifying this equipment assumes all risks and full responsibility for all damages or injury which may result from incorrect assembly or modification. This product must be modified by competent professionals only.

Specification
Webbing	25 mm
Connector	TORX 20
Construction	Polyester
Stitches	One End
Rivets	Provided
Left and Right	YES

The treeMOTION Pro Hip/Leg is a genuine replacement part from Teufelberger. This spare part should be replaced only by a suitably qualified person. Using a Torx 20, remove the connecting bolt on the black ring and slide out the spacer. Remove the damaged Hip-to-Leg webbing and insert the genuine replacement. Ensure the stitched tab end faces the harness when reconnecting to the black ring. It's best to complete this task one side at a time so you can use the other side as a reference. Thread the end of the webbing through the upper slot of the front hardware. Take care to ensure that the webbing passes from the middle of the harness toward the outer side of the harness. Pass the webbing through the loop of elastic material included in the replacement kit. Ensure that the two adjuster buckle parts are sitting correctly. Pass the webbing through the slot closest to the waist belt. Now, pass the webbing over the centre rib of the buckle and thread it through the slot closest to the webbing keeper that holds the two buckle parts together. You can refer to the opposite side if you lose your way. Check the buckle assembly for the correct function before proceeding. Pass the webbing through the loop of elastic material again. Before proceeding, ensure that all parts are in the correct place, not twisted and that the buckles function correctly. Insert the lower rivet part through the folded-up strap and connect it to the upper rivet part it to the upper rivet part. Place the strap on a solid surface, and use a hammer to drive the rivet into place. Consider using the DMM Webbing Stopper Kit as an alternative to rivets.

FREE SHIPPING on orders over $250. NO INTERNATIONAL SHIPPING.

Under $250
Auckland	$6.90
North Island	$9.90
South Island	$12.90
Orders Over $250	FREE*

Orders with Rural Delivery addresses may take longer than stated to arrive.

SUPPLY CHAIN DISRUPTION

Due to factors out of our control, Treetools is experiencing random shipping delays and supply issues that may result in some gear not being available either in-store and/or online. We apologise for any inconvenience this may cause.

*Free Shipping excludes ladders and overweight product.

NO INTERNATIONAL SHIPPING Treetools is a 'kiwi only' affair.
Find out more about Treetools Shipping and Return Policy here.
All parcels require a signature on delivery unless requested otherwise.

Accurately tracking the life of a product is paramount for your safety

At Treetools, we prioritize your safety above all else, so we cannot accept returns on safety equipment. This policy ensures that your gear is always brand new, safe, and traceable to our trusted manufacturers and suppliers. We understand the critical role this equipment plays in your safety, potentially even preserving your life during climbs or work aloft. Therefore, we urge you to choose carefully before making your purchase. Additionally, please note that suitably trained and qualified individuals should use the climbing and rigging equipment listed on our website. We want to reassure you of our unwavering commitment to safety. Thank you for your understanding and commitment to safety.

Non-Returnable Items: Due to safety and hygiene reasons, PPE gear that has been opened, used, or worn cannot be returned. This includes, but is not limited to, helmets, lanyards, harnesses, friction cords and ropes.

Return Conditions for Unused Items: Return Conditions for Unused Items: Unused items in their original, unopened packaging with intact seals can be returned within 30 days of purchase with proof of purchase.

Defective Products: Items with manufacturer defects can be returned or exchanged within the warranty period, regardless of packaging status. Please contact customer service for return authorization (RMA) and instructions.

Documentation Required: Proof of purchase and return authorization are required for all returns. Inspection Process: All returned items will undergo a rigorous inspection to ensure they meet return criteria. Items failing inspection will be returned to the customer.

Refund and Exchange Options: Refunds will be issued to the original payment method or as store credit. Exchanges are subject to availability.

Restocking Fee: 15% restocking fee for non-defective returns.

It is crucial that you select compatible gear for your specific configuration to ensure maximum safety. Failure to do so may result in severe consequences. We highly recommend that you choose the correct diameter rope that matches the hardware you are using. Please note that safety products cannot be returned due to configuration incompatibility. Therefore, we strongly advise you to conduct thorough research or ask us for clarification before making a purchase. Your safety is our top priority.